- Disable ctrl commands hyperterm password#
- Disable ctrl commands hyperterm Pc#
- Disable ctrl commands hyperterm series#
- Disable ctrl commands hyperterm mac#
Output from other switchesĮnter " n" at the prompt to abort the initial configuration dialog. Loading "flash:".#įile "flash:" uncompressed and installed, entry po Issue the boot command to boot the system.
Disable ctrl commands hyperterm password#
!- The config.text file contains the password switch: rename flash:config.text flash:config.old Type rename flash:config.text flash:config.old to rename the configuration file. The switch file system is displayed: switch: dir flash:Ģ -rwx 1803357 !- This is the current version of software.Ĥ -rwx 1131 config.text !- This is the configuration file.Ĥ03968 bytes available (3208704 bytes used) Note: Make sure to type a colon (:) after the dir flash. The system has been interrupted prior to initializing the flash file system to finishĤ. !- Ctrl+Break is entered using Hyperterm. !- Wait until you see this message before !- you issue the break sequence. Send break character to prevent autobooting. *** The system will autoboot in 15 seconds *** Parameter Block Filesystem (pb:) installed, fsid: 4
Disable ctrl commands hyperterm mac#
C2955 Boot Loader (C2955-HBOOT-M) Version 12.1(0.0.514), CISCO DEVELOPMENT TESTīase ethernet MAC Address: 00:0b:be:b6:ee:00įlashfs: 0 orphaned files, 0 orphaned directoriesīoot Sector Filesystem (bs:) installed, fsid: 3 The next example uses Hyperterm to break into switch: mode on a 2955. For more information, refer to Standard Break Key Sequence Combinations During Password Recovery. On a workstation that runs UNIX, Ctrl-C is the break key. Hyperterm that runs on Windows 2000 uses Ctrl + Break. The break sequence is determined by the terminal application and operating system used. Instead, the switch boot loader uses the break-key detection to stop the automatic boot sequence for the password recovery purposes.
Disable ctrl commands hyperterm series#
The Catalyst 2955 series switches do not use an external mode button for password recovery. Note: LED position can vary slightly based on the model. When you release the Mode button, the SYST LED blinks green. Release the Mode button after approximately 15 seconds when the SYST LED turns solid green. When you release the Mode button, the SYSTLED blinks green. Release the Mode button when the SYSTLED blinks amber and then turns solid green. When you release the Mode button, the SYSTLED blinks amber. Release the Mode button after approximately 5 seconds when the Status ( STAT) LED goes out. Release the Mode button when the LED over Port1xgoes out. LED Behavior and Mode Button Release Action Hold down the mode button located on the left side of the front panel, while you reconnect the power cable to the switch. Note: For additional information on cabling and connecting a terminal to the console port, refer to Connect a Terminal to the Console Port on Catalyst Switches.
Disable ctrl commands hyperterm Pc#
Recovery ProcedureĪttach a terminal or PC with terminal emulation (for example, Hyper Terminal) to the console port of the switch. This document describes the password recovery procedure for the Cisco Catalyst Layer 2 fixed configuration switches 2900XL/3500XL, 2940, 2950/2955, 2960, and 2970 Series, as well as the Cisco Catalyst Layer 3 fixed configuration switches 3550, 3560, and 3750 Series. Conventionsįor more information on document conventions, see the Cisco Technical Tips Conventions. If your network is live, ensure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.
There are no specific requirements for this document. This document describes the password recovery procedure for the Cisco Catalyst Layer 2 and Cisco Catalyst Layer 3 fixed configuration switches.
0 kommentar(er)
